URBAN SM110 with conveyor 2,6 m

« »

The branch logger URBAN SM110 is powered by a 35 hp Briggs & Stratton VANGUARD engine. The SM110 is mounted on a solid frame and is designed for stationary use. This model is very ideal for processing waste material (boards up to width 280 mm, cut-offs) and also smaller stems up to 12 cm diameter. The final length of chips is 7 -22 cm.

UP TO DIAMETER 120 MM

Part of the machine is: electric starter of motor including battery, hour meter, operators manual including declaration of conformity

Category: URBAN SM110
Model series:110
Catalogues code:SM110 D2,6
Offered from:05.02.2021
Availability :within 3 weeks

Product variants

Photo	Variant
	URBAN SM110 with Big-bag bagging within 3 weeks
	URBAN SM110 with folding conveyor 4,1 m within 3 weeks
	URBAN SM110 with double bagging within 3 weeks

Weight (kg): 1020

Max. diameter of soft freshwood (pine): 120 mm

Max. diameter of fresh hardwood (oak, hornbeam): 100 mm

Max. diameter of dry hardwood (oak, hornbeam): 80 mm

Max. diamensions of block of wood (spruce): 100 x 100 mm

Max. diameter of wooden board (spruce): 280 x 40 mm

Log length (not adjustable): 7 - 22 cm

Logging device inlet dimensions: 290 x 290 mm

Inlet hopper dimensions: 800 x 600 mm

Blade rotation speed (rpm): 170 / min.

Top performance: 10 m3/h

Engine power: 26,1 kW (35 hp)

Fuel: Unleaded fuel (95)

Fuel tank volume: 15 l

Average gas consumption: 3 - 4 l/h

Electric start of motor: Yes

Hour meter + tachometer: Yes

Number of logging blades: 6

The gap between the blade of the cutting blades: approx. 0,1 mm

Lifetime of blades per one grinding: 150 - 800 m3 of of small logs

Overload protection: Belt slip

Dimensions (length x width x height): 256 x 150 x 170 cm

Logs output: Double bagging

The engine

The SM110 is driven by a 35 hp Briggs & Stratton VANGUARD engine with electric start, an oil level and fuel indicators and an hour meter. The fuel tank capacity is 15 litres. The engine´s output is transferred via V-belts to the oil filled gearbox which drives the blade rotors.

The frame

The SM110 is designed for stationary using. The machine frame has 4 rigid legs and its lower part is adapted for forklift trucks. Two suspension lugs at the top of the machine can also be used for handling.

The inlet hopper

The hopper is long enough to provide safety and is equipped with a safety shut-off frame, which by pressing down stops the engine. The inlet hopper is oriented horizontally, which greatly facilitates insertion of long branches compared to the vertical or sloping hopper. Surface treatment of the whole machine is made with powder paint.

The belt conveyor

The conveyor is driven by V-belt drive. The slope of the conveyor is adjustable by means of a winch. The conveyor is lifted to a vertical position during transport. As an optional accessory, it is possible to mount a slide with length 1m or double bagging device with a support leg at the end of the conveyor or. The bagging device is secured by four screws and it takes only a few minutes to fit it.

The overloading protection

A belt slip protects the device from overloading. If a too strong branch is inserted, the belt will be slipped and the engine stopped. If they do, the knife blades will usually be bite in the branch and can not be freely removed from the hopper. The supplied lever is used to release it. Release the branch by clockwise lever rotating.

The chipping device

The working principle of branch loggers URBAN lies in two counter rotating shafts with knives. The rotating knives draw in the wood material into the feed hopper unassisted. The passage gap between the shafts is 110 mm. Each shaft has 3 fixed knives, made from high quality tool steel. It is possible to resharpen the knives repeatedly. After sharpening there is a pad to be put under the knives in order to keep the same gap between the knives (c. 0,1 mm). One single sharpening of knives is capable of producing from 150 to 800 solid meters of small logs, depending the level of contaminants (mud, nails, stones etc.). Each blade can be sharpened up about 4 mm, then it must be replaced with a new one.